Cyrus 4 in 1 Sensor wird nicht richtig erkannt

Einrichtung der openHAB Umgebung und allgemeine Konfigurationsthemen.

Moderatoren: seppy, udo1toni

Antworten
salamander070
Beiträge: 40
Registriert: 16. Nov 2018 15:37
Wohnort: S-H

Cyrus 4 in 1 Sensor wird nicht richtig erkannt

Beitrag von salamander070 »

Hallo
haben mir den Cyrus 4in1 Sensor geholt und konnte diesen auch in openhab einbinden, aber leider zeigt openhab an, dass er das Gerät nicht einordnen kann.

Code: Alles auswählen

This device has not been fully discovered by the binding. There are a few possible reasons for this -:

    The device is not in the database. If the device attributes show that this device has a valid manufacturer ID, device ID and type, then this is likely the case (eg. you see a label like "Z-Wave node 1 (0082:6015:020D::2.0)"). Even if the device appears to be in the database, some manufacturers use multiple sets of references for different regions or versions, and your device references may not be in the database. In either case, the database must be updated and you should raise an issue to get this addressed.
    The device initialisation is not complete. Once the device is included into the network, the binding must interrogate it to find out what type of device it is. One part of this process is to get the manufacturer information required to identify the device, and until this is done, the device will remain unknown. For mains powered devices, this will occur quickly, however for battery devices the device must be woken up a number of times to allow the discovery phase to complete. This must be performed with the device close to the controller. 
In Z-Wave Bindung taucht das Gerät leider nicht auf.
Gelöst zumindest etwas. Musste erneut die Knopf am Sensor drücken, damit noch mehr verhandelt wird und 30cm entfernt vom USB Stick. Vorher war ich zwei Stockwerke entfernt. Aber das Einbinden und auch das Ausbinden erklärt sich mir noch nicht so.

Benutzeravatar
sihui
Beiträge: 1827
Registriert: 11. Apr 2018 19:03
Answers: 21

Re: Cyrus 4 in 1 Sensor wird nicht richtig erkannt

Beitrag von sihui »

salamander070 hat geschrieben: 27. Nov 2018 20:22 Aber das Einbinden und auch das Ausbinden erklärt sich mir noch nicht so.
Mit Einbinden (Inkludieren) fügst du deine Geräte dem Zwave Controller und damit dem Zwave Netzwerk hinzu, mit Ausbinden (Exkludieren) löscht du es wieder von deinem Controller.
Batteriebetriebene Geräte müssen mehrfach manuell aufgeweckt werden um die Initialisierung (also das Erkennen des neuen Gerätes im Zwave Binding nach Inkludierung) abzuschließen, bei netzbetriebenen Geräten ist das nicht notwendig.
Eine abgeschlossene Initialisierung erkennst du an einer neu angelegten xml Datei in deinem /userdata/zwave Ordner.
openHAB3 mit Zwave, Alexa, ESPEasy, MQTT, Logitech Harmony, Philips HUE und ZigBee Hardware auf Proxmox VE.

HABuser
Beiträge: 45
Registriert: 15. Jan 2019 17:34

Re: Cyrus 4 in 1 Sensor wird nicht richtig erkannt

Beitrag von HABuser »

Hallo,
Ich habe auch diesen Cyrus 4in1 Sensor. Mit Openhab 2.4 mit dem enthaltenen Zwave Bindung wurde dieses Gerät bei mir auch nicht erkannt. Mit dem 2.5 Snapshot klappte es aber auf Anhieb. Irgendwo im englischen Forum gibt es auch einen Hinweis darauf. Bei mir wird der nun als
ZSE40 Zooz 4-in-one motion/temperature/humidity/luminance sensor
erkannt.

Antworten