Openhabian und Homegear kein pairing

[Blaccky]

Hallo,

und zwar habe ich auf Openhabian, Homegear installiert und mit einer anderen SD-Karte meine HM-MOD-RPI-PCB, über Yahm auf den neusten Firmware stand gebracht (2.8.5?).

Nun wollte ich mit dem Befehl "pon" in Homegear meinen Funk Heizkörperthermostat von Homematic verbinden doch leider ohne Erfolg.

Die Config.txt und cmdline.txt wurden nach Anleitungen geändert und sehen so aus:

config.txt:

Code: Alles auswählen

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

dtoverlay=pi3-miniuart-bt
dtparam=spi=on
enable_uart=1
gpu_mem=16
dtparam=i2c_arm=on

cmdline.txt:

Code: Alles auswählen

dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=9bff6b8e-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait

Homegear.log:

Code: Alles auswählen

04/24/18 19:21:44.380 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:44.380 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:45.956 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:45.956 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connecting to HM-MOD-RPI-PCB...
04/24/18 19:21:47.957 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connected to HM-MOD-RPI-PCB.
04/24/18 19:21:47.957 Debug: GPIO 18 set to 0.
04/24/18 19:21:48.057 Debug: GPIO 18 set to 1.
04/24/18 19:21:48.093 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD000C000000436F
04/24/18 19:21:48.094 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 5F4350555F424C72
04/24/18 19:21:48.094 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 51
04/24/18 19:21:48.094 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000C000000436F5F4350555F424C7251
04/24/18 19:21:49.094 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Sending: FD0003000003180A
04/24/18 19:21:49.625 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD00040000040199
04/24/18 19:21:49.626 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 3D
04/24/18 19:21:49.626 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000400000401993D
04/24/18 19:21:49.664 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD0010FE01004475
04/24/18 19:21:49.665 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 616C436F50726F5F
04/24/18 19:21:49.666 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 417070B736
04/24/18 19:21:49.666 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD0010FE01004475616C436F50726F5F417070B736
04/24/18 19:21:54.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:54.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:55.671 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:55.671 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connecting to HM-MOD-RPI-PCB...
04/24/18 19:21:56.029 RPC Server (Port 2001): Debug: Packet received: 42696E000000001C0000000470696E670000000100000003000000086332653539663437
04/24/18 19:21:56.029 RPC Server (Port 2001): Info: Client number 16 is calling RPC method: ping (2) Parameters:
(String) c2e59f47
04/24/18 19:21:56.029 RPC Server (Port 2001): Response: 
(Boolean) 1
04/24/18 19:21:56.029 RPC client: Debug: Calling RPC method "system.multicall" on server 192.168.0.104.
04/24/18 19:21:56.029 RPC client: Parameters:
04/24/18 19:21:56.029 RPC Server (Port 2001): Response binary:
42696E01000000050000000201
(Array length=1)
{
  (Struct length=2)
  {
    [methodName]
    {
      (String) event
    }
    [params]
    {
      (Array length=4)
      {
        (String) RF-c2e59f47
        (String) CENTRAL
        (String) PONG
        (String) c2e59f47
      }
    }
  }
}
04/24/18 19:21:56.029 Debug: Calling getFileDescriptor...
04/24/18 19:21:56.030 Debug: Connecting to host 192.168.0.104 on port 9126...
04/24/18 19:21:56.030 Debug: Connected to host 192.168.0.104 on port 9126. Client number is: 206
04/24/18 19:21:56.031 RPC client: Debug: Sending packet: 42696E00000000930000001073797374656D2E6D756C746963616C6C00000001000001000000000100000101000000020000000A6D6574686F644E616D6500000003000000056576656E7400000006706172616D730000010000000004000000030000000B52462D6332653539663437000000030000000743454E5452414C0000000300000004504F4E4700000003000000086332653539663437
04/24/18 19:21:56.032 RPC client: Debug: Packet received: 42696E0100000015000001000000000100000003000000056576656E74
04/24/18 19:21:56.033 RPC client: Debug: Received packet from server 192.168.0.104: 42696E0100000015000001000000000100000003000000056576656E74
04/24/18 19:21:56.033 RPC client: Response was:
(Array length=1)
{
  (String) event
}
04/24/18 19:21:57.672 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connected to HM-MOD-RPI-PCB.
04/24/18 19:21:57.672 Debug: GPIO 18 set to 0.
04/24/18 19:21:57.772 Debug: GPIO 18 set to 1.
04/24/18 19:21:57.808 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD000C000000436F
04/24/18 19:21:57.809 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 5F4350555F424C72
04/24/18 19:21:57.809 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 51
04/24/18 19:21:57.809 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000C000000436F5F4350555F424C7251
04/24/18 19:21:58.809 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Sending: FD0003000003180A
04/24/18 19:21:59.340 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD00040000040199
04/24/18 19:21:59.345 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 3D
04/24/18 19:21:59.345 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000400000401993D
04/24/18 19:21:59.379 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD0010FE01004475
04/24/18 19:21:59.380 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 616C436F50726F5F
04/24/18 19:21:59.381 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 417070B736
04/24/18 19:21:59.381 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD0010FE01004475616C436F50726F5F417070B736
04/24/18 19:22:03.810 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:22:03.810 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:22:05.385 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:22:05.386 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connecting to HM-MOD-RPI-PCB...
04/24/18 19:22:07.386 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Connected to HM-MOD-RPI-PCB.
04/24/18 19:22:07.387 Debug: GPIO 18 set to 0.
04/24/18 19:22:07.487 Debug: GPIO 18 set to 1.
04/24/18 19:22:07.522 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD000C000000436F
04/24/18 19:22:07.523 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 5F4350555F424C72
04/24/18 19:22:07.523 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 51
04/24/18 19:22:07.524 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000C000000436F5F4350555F424C7251
04/24/18 19:22:08.524 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Sending: FD0003000003180A
04/24/18 19:22:09.055 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD00040000040199
04/24/18 19:22:09.055 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 3D
04/24/18 19:22:09.055 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD000400000401993D
04/24/18 19:22:09.093 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: FD0010FE01004475
04/24/18 19:22:09.094 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 616C436F50726F5F
04/24/18 19:22:09.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received. Raw data: 417070B736
04/24/18 19:22:09.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Debug: Packet received from HM-MOD-RPI-PCB: FD0010FE01004475616C436F50726F5F417070B736

Homegear.err:

Code: Alles auswählen

04/24/18 19:19:57.513 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:19:59.089 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:07.228 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:07.229 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:08.805 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:16.944 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:16.944 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:18.520 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:26.659 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:26.659 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:28.235 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:36.375 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:36.375 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:37.951 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:46.090 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:46.090 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:47.666 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:20:55.805 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:20:55.805 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:20:57.381 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:05.520 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:05.521 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:07.096 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:15.235 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:15.236 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:16.812 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:24.951 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:24.951 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:26.527 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:34.666 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:34.666 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:36.241 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:44.380 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:44.380 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:45.956 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:21:54.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:21:54.095 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:21:55.671 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...
04/24/18 19:22:03.810 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: No response received to packet: FD0003000003180A
04/24/18 19:22:03.810 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Error: Unknown packet received in response to init packet. Reconnecting...
04/24/18 19:22:05.385 Module HomeMatic BidCoS: HM-MOD-RPI-PCB "My-HM-MOD-RPI-PCB": Warning: Connection closed (1). Trying to reconnect...

Hoffe es erkennt jemand den Fehler und kann mein Problem lösen

Danke schonmal & LG

[surfa]

Hallo Blaccky,
ich habe in den letzten Tagen ein ähnliches Problem mit meinem Raspi3 gehabt. Bei RaspberryMatic funktioniert alles einwandfrei, ich wollte allerdings zu OpenHABian wechseln.
Homegear schafft es aus irgendeinem Grund nicht Pakete mit dem Funkmodul (HM-MOD-RPI-PCB, Firmware 2.8.5) auszutauschen, daher funktioniert dann auch kein Pairing.
Es gibt verschiedene Threads zu dem Thema die ich alle durchgearbeitet habe, leider bisher auch nur mit mäßigem Erfolg.
Z.B: https://community.openhab.org/t/openhab ... i/23578/11
Wenn man in "sudo openhabian-config" unter "System Configuration > Serial Port" folgende Optionen setzt:
[x] Disable Serial Ports
[x] Disable Bluetooth
[] Add to JVM
Muss man anscheinend weder die /boot/config.txt noch /boot/cmdline.txt manuell editieren. "Disable serial interface" aus der Homegear Doku ist dann auch nicht nötig, sondern nur die Anpassung der homegearbidcos.conf: https://doc.homegear.eu/data/homegear-h ... od-rpi-pcb
Danach werden zwar Pakete ausgetauscht, die sind aber entweder zu lang oder zu kurz. Das Setting "core_freq", was an manchen Stellen empfohlen wurde ändert daran auch nichts.
Hast du mittlerweile eine Lösung für das Problem gefunden?
Ich überlege als nächstes auf YAHM-LXC umzusteigen.....

[BOP]

Hallo!

Nun wollte ich mit dem Befehl "pon" in Homegear meinen Funk Heizkörperthermostat von Homematic verbinden doch leider ohne Erfolg.

Sind die Thermostate nicht Homematic IP Geräte? Als ich damals Homegear ausprobierte, konnte das nur BidCoS. Also kein IP.

Bin dann bei PiVCCU gelandet. War imho auch einfacher zu installieren.

[surfa]

Hi BOP,
es gibt Heizkörperthermostate von Homematic (https://www.elv.de/homematic-heizkoerpe ... tat-1.html) und von Homematic IP (https://www.elv.de/homematic-ip-heizkoe ... ostat.html).
Die von Homematic haben noch Bedienelemente.
Ich habe für das Problem auch mal in einem Thread im Homegear Forum aufgemacht. Mal schauen, ob jemand helfen kann: https://forum.homegear.eu/t/Homegear-no ... PCB/1073/3