was ist das HLW: EPC 2, CFlen?

[MagicBird]

Hallo Forum,

habe mir die Eightree Steckdosen geholt und diese auch nicht weiter herum gespielt mit.
Daher nur das Mqtt eingerichtet, den name angepasst und eine Zeitschalte aktiviert.

Nun laufe ich am Netzwerkswitch vorbei und sehe die LED aktivitäten und wunderte mich warum die Traffic so intensiv ist.
Habe mit dem PI den Mqtt Traffic mal mitgelesen...

Code: Alles auswählen

stat/colin_weihnachten/LOGGING 20:56:06.670 HLW: EPC 2, CFlen 508879 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:06.808 HLW: EPC 22, CFlen 46623 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:07.402 WIF: Checking connection...
stat/wohnzimmer_tannebaum/LOGGING 20:56:07.808 HLW: EPC 21, CFlen 46531 usec
stat/kuechen_fenster/LOGGING 20:56:07.798 HLW: EPC 2, CFlen 491096 usec
stat/colin_weihnachten/LOGGING 20:56:07.670 HLW: EPC 2, CFlen 480646 usec
tele/aussen_bmp280/temperature 3.57
tele/bad_wlandose/STATE {"Time":"2024-12-14T20:56:08","Uptime":"27T16:02:54","UptimeSec":2390574,"Heap":25,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":15,"POWER":"OFF","Wifi":{"AP":2,"SSId":"Mit Sicherheit Fort KnoxF","BSSId":"48:EE:0C:64:6A:68","Channel":8,"Mode":"11n","RSSI":76,"Signal":-62,"LinkCount":14,"Downtime":"0T00:06:41"}}
tele/bad_wlandose/SENSOR {"Time":"2024-12-14T20:56:08","AM2301":{"Temperature":21.2,"Humidity":51.0,"DewPoint":10.6},"TempUnit":"C"}
tele/aussen_bmp280/pressure 1006.43
stat/kuechen_fenster/LOGGING 20:56:08.798 HLW: EPC 2, CFlen 516361 usec
tele/aussen_bme280/temperature 1.82
stat/colin_weihnachten/LOGGING 20:56:08.670 HLW: EPC 2, CFlen 526049 usec
tele/aussen_bme280/humidity 86.10
stat/wohnzimmer_tannebaum/LOGGING 20:56:08.808 HLW: EPC 21, CFlen 46599 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:09.808 HLW: EPC 22, CFlen 46690 usec
stat/kuechen_fenster/LOGGING 20:56:09.798 HLW: EPC 2, CFlen 531835 usec
tele/aussen_bme280/pressure 1005.98
stat/colin_weihnachten/LOGGING 20:56:09.670 HLW: EPC 2, CFlen 521393 usec
stat/kuechen_fenster/LOGGING 20:56:10.798 HLW: EPC 2, CFlen 493811 usec
stat/colin_weihnachten/LOGGING 20:56:10.670 HLW: EPC 2, CFlen 497773 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:10.808 HLW: EPC 21, CFlen 46842 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:11.808 HLW: EPC 21, CFlen 46919 usec
stat/kuechen_fenster/LOGGING 20:56:11.798 HLW: EPC 2, CFlen 499608 usec
stat/colin_weihnachten/LOGGING 20:56:11.670 HLW: EPC 2, CFlen 510122 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:12.808 HLW: EPC 22, CFlen 47128 usec
stat/kuechen_fenster/LOGGING 20:56:12.798 HLW: EPC 2, CFlen 511977 usec
stat/wohnzimmer_blume/LOGGING 20:56:12.275 BRY: GC from 8933 to 4463 bytes, objects freed 21/44 (in 1 ms) - slots from 46/91 to 46/91
stat/colin_weihnachten/LOGGING 20:56:12.670 HLW: EPC 2, CFlen 509648 usec
stat/kuechen_fenster/LOGGING 20:56:13.798 HLW: EPC 2, CFlen 513697 usec
stat/colin_weihnachten/LOGGING 20:56:13.670 HLW: EPC 2, CFlen 529449 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:13.808 HLW: EPC 21, CFlen 46643 usec
stat/wohnzimmer_tannebaum/LOGGING 20:56:14.808 HLW: EPC 22, CFlen 46806 usec

warum wird soviel HLW gesendet?
Kann man das abschalten?

danke

[udo1toni]

Wenn es sich um dieses Modell handelt: https://templates.blakadder.com/eightree_16A.html ist ja schon Tasmota auf den Teilen drauf.
Welche genaue Version ist installiert?
Mein Ratschlag Nr. 1 wäre, die Firmware auf die aktuelle Version zu bringen. Je nach Stand kann es sein, dass Du (mehrere) Zwischenschritte dafür machen musst, falls aber eine Firmware jünger als 9.1 vorliegt, kannst Du direkt auf die aktuelle Version 14.4.0 updaten.
Denke daran, dass Du die Geräte vermutlich zunächst "eichen" musst, am besten geht das mit einer rein ohmschen Last (eine 230V/60W Glühlampe wäre jetzt gut). Die notwendigen Schritte sind in der Tasmota Dokumentation beschrieben.

Was das Logging betrifft, so kannst Du das gewöhnlich abschalten: WebUI der Steckdose -> Einstellungen -> Logging -> MQTT -> keine.
Normalerweise ist das gar nicht aktiv, kann aber sein, dass der Hersteller das beim Testen aktiviert, und später vergessen hat, es wieder abzuschalten...

[MagicBird]

Hallo Udo,

entschuldige die späte antwort.

Leider habe ich derzeit keine Glühlampe im Haushalt, aber das werde ich entsprechend nachholen.

ja die Firmware, ist schwierig drauf zuflashen.
wie auch immer habe ich eben die erste der 4 dosen auf 14.4.1 auf das neuste Update bekommen.

Code: Alles auswählen

08:53:01.011 MQT: Connected
08:53:01.017 MQT: tele/wohnzimmer_tannebaum/LWT = Online (retained)
08:53:01.020 MQT: cmnd/wohnzimmer_tannebaum/POWER = 
08:53:01.022 MQT: Subscribe to cmnd/wohnzimmer_tannebaum/#
08:53:01.038 MQT: Subscribe to cmnd/tasmotas/#
08:53:01.040 MQT: Subscribe to cmnd/DVES_A4EAE8_fb/#
08:53:01.045 MQT: tele/wohnzimmer_tannebaum/INFO1 = {"Info1":{"Module":"EIGHTREE","Version":"14.4.1(release-tasmota32)","FallbackTopic":"cmnd/DVES_A4EAE8_fb/","GroupTopic":"cmnd/tasmotas/"}}
08:53:01.065 MQT: tele/wohnzimmer_tannebaum/INFO2 = {"Info2":{"WebServerMode":"Admin","Hostname":"wohnzimmer-tannebaum-2792","IPAddress":"192.168.5.134","IP6Global":"2003:ea:d73f:3400:4a27:e2ff:fea4:eae8","IP6Local":"fe80::4a27:e2ff:fea4:eae8%st1"}}
08:53:01.102 MQT: tele/wohnzimmer_tannebaum/INFO3 = {"Info3":{"RestartReason":"Software reset digital core","BootCount":22}}
08:53:01.111 MQT: stat/wohnzimmer_tannebaum/RESULT = {"POWER":"OFF"}
08:53:01.114 MQT: stat/wohnzimmer_tannebaum/POWER = OFF
08:53:01.117 TFS: File 'autoexec.bat' not found
08:53:01.587 WIF: IPv6 Global 2003:ea:d73f:3400:4a27:e2ff:fea4:eae8
08:53:02.560 QPC: Reset
08:53:04.557 APP: Boot Count 22
08:53:05.615 BRY: GC from 6853 to 4607 bytes, objects freed 21/46 (in 1 ms) - slots from 77/91 to 50/91
08:53:05.623 MQT: tele/wohnzimmer_tannebaum/STATE = {"Time":"2024-12-17T08:53:05","Uptime":"0T00:00:10","UptimeSec":10,"Heap":178,"SleepMode":"Dynamic","Sleep":5,"LoadAvg":199,"MqttCount":1,"Berry":{"HeapUsed":4,"Objects":46},"POWER":"OFF","Wifi":{"AP":1,"SSId":"Mit Sicherheit Fort Knox","BSSId":"CC:CE:1E:39:45:A6","Channel":8,"Mode":"HT40","RSSI":46,"Signal":-77,"LinkCount":1,"Downtime":"0T00:00:04"}}
08:53:05.675 MQT: tele/wohnzimmer_tannebaum/SENSOR = {"Time":"2024-12-17T08:53:05","ENERGY":{"TotalStartTime":"2024-12-17T08:53:01","Total":0.06515,"Yesterday":0.20125,"Today":0.06515,"Period":0,"Power":0,"ApparentPower":0,"ReactivePower":0,"Factor":0.00,"Voltage":231,"Current":0.000},"ESP32":{"Temperature":62.3},"TempUnit":"C"}
08:53:07.005 CFG: Energy saved to file
08:53:07.146 CFG: Saved, Count 103, Bytes 4096
08:53:09.757 HTP: Tools
08:53:10.581 MQT: tasmota/discovery/4827E2A4EAE8/config = {"ip":"192.168.5.134","dn":"wohnzimmer_tannebaum","fn":["wohnzimmer_tannebaum",null,null,null,null,null,null,null],"hn":"wohnzimmer-tannebaum-2792","mac":"4827E2A4EAE8","md":"EIGHTREE","ty":0,"if":0,"ofln":"Offline","onln":"Online","state":["OFF","ON","TOGGLE","HOLD"],"sw":"14.4.1","t":"wohnzimmer_tannebaum","ft":"%prefix%/%topic%/","tp":["cmnd","stat","tele"],"rl":[1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"swc":[-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1],"swn":[null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null,null],"btn":[1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"so":{"4":0,"11":0,"13":0,"17":0,"20":0,"30":0,"68":0,"73":1,"82":0,"114":0,"117":0},"lk":0,"lt_st":0,"bat":0,"dslp":0,"sho":[],"sht":[],"ver":1} (retained)
08:53:10.681 MQT: tasmota/discovery/4827E2A4EAE8/sensors = {"sn":{"Time":"2024-12-17T08:53:10","ENERGY":{"TotalStartTime":"2024-12-17T08:53:01","Total":0.06515,"Yesterday":0.06515,"Today":0.00000,"Power":0,"ApparentPower":0,"ReactivePower":0,"Factor":0.00,"Voltage":232,"Current":0.000},"ESP32":{"Temperature":62.3},"TempUnit":"C"},"ver":1} (retained)
08:53:11.057 HTP: Console
08:53:20.240 WIF: Checking connection...
08:53:23.843 BRY: GC from 9300 to 4813 bytes, objects freed 20/46 (in 0 ms) - slots from 52/91 to 50/91
08:53:40.256 WIF: Checking connection...
08:53:46.839 BRY: GC from 9629 to 4813 bytes, objects freed 23/46 (in 0 ms) - slots from 50/91 to 50/91
08:54:00.240 WIF: Checking connection...
08:54:09.839 BRY: GC from 9654 to 4813 bytes, objects freed 23/46 (in 0 ms) - slots from 52/91 to 50/91
08:54:20.240 WIF: Checking connection...
08:54:33.841 BRY: GC from 9796 to 4813 bytes, objects freed 24/46 (in 0 ms) - slots from 50/91 to 50/91
08:54:40.232 WIF: Checking connection...
08:54:57.840 BRY: GC from 9796 to 4813 bytes, objects freed 24/46 (in 0 ms) - slots from 50/91 to 50/91
08:55:00.234 WIF: Checking connection...
08:55:20.240 WIF: Checking connection...
08:55:21.840 BRY: GC from 9828 to 4813 bytes, objects freed 24/46 (in 1 ms) - slots from 51/91 to 50/91
08:55:40.235 WIF: Checking connection...
08:55:45.843 BRY: GC from 9796 to 4813 bytes, objects freed 24/46 (in 0 ms) - slots from 50/91 to 50/91

dann habe ich 2 mit der Version Tasmota 14.1.0.3 (fee5251-tasmota)

Code: Alles auswählen

09:03:04.471 MQT: tele/lennox_netzwerk1/STATE = {"Time":"2024-12-17T09:03:04","Uptime":"7T19:28:53","UptimeSec":674933,"Heap":23,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"POWER":"ON","Wifi":{"AP":1,"SSId":"Mit Sicherheit Fort KnoxF","BSSId":"48:EE:0C:64:6A:68","Channel":8,"Mode":"11n","RSSI":86,"Signal":-57,"LinkCount":1,"Downtime":"0T00:00:06"}}
09:03:04.481 MQT: tele/lennox_netzwerk1/SENSOR = {"Time":"2024-12-17T09:03:04","ENERGY":{"TotalStartTime":"2023-12-28T12:27:29","Total":6.820,"Yesterday":0.018,"Today":0.003,"Period":0,"Power":1,"ApparentPower":2,"ReactivePower":2,"Factor":0.44,"Voltage":227,"Current":0.010}}
09:03:34.515 MQT: tele/lennox_netzwerk1/STATE = {"Time":"2024-12-17T09:03:34","Uptime":"7T19:29:23","UptimeSec":674963,"Heap":23,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"POWER":"ON","Wifi":{"AP":1,"SSId":"Mit Sicherheit Fort KnoxF","BSSId":"48:EE:0C:64:6A:68","Channel":8,"Mode":"11n","RSSI":88,"Signal":-56,"LinkCount":1,"Downtime":"0T00:00:06"}}

die sind ganz entspannd.

und eine mit Tasmota 12.5.0.1

Code: Alles auswählen

09:01:27.251 MQT: tele/kuechen_fenster/STATE = {"Time":"2024-12-17T09:01:27","Uptime":"7T19:30:40","UptimeSec":675040,"Heap":187,"SleepMode":"Dynamic","Sleep":5,"LoadAvg":199,"MqttCount":2,"Berry":{"HeapUsed":4,"Objects":44},"POWER":"OFF","Wifi":{"AP":2,"SSId":"Mit Sicherheit Fort Knox","BSSId":"CC:CE:1E:39:45:A6","Channel":8,"Mode":"11n","RSSI":60,"Signal":-70,"LinkCount":1,"Downtime":"0T00:00:04"}}
09:01:27.278 MQT: tele/kuechen_fenster/SENSOR = {"Time":"2024-12-17T09:01:27","ENERGY":{"TotalStartTime":"1970-01-01T00:00:00","Total":0.66860,"Yesterday":0.03066,"Today":0.01002,"Period":0,"Power":0,"ApparentPower":0,"ReactivePower":0,"Factor":0.00,"Voltage":238,"Current":0.000},"ESP32":{"Temperature":60.5},"TempUnit":"C"}
09:01:31.490 WIF: Checking connection...
09:01:51.491 WIF: Checking connection...
09:02:11.491 WIF: Checking connection...
09:02:31.490 WIF: Checking connection...
09:02:43.190 BRY: GC from 8528 to 4463 bytes, objects freed 18/44 (in 1 ms) - slots from 47/91 to 46/91
09:02:51.491 WIF: Checking connection...
09:03:11.485 WIF: Checking connection...
09:03:31.490 WIF: Checking connection...
09:03:51.492 WIF: Checking connection...
09:04:11.492 WIF: Checking connection...
09:04:19.790 BRY: GC from 8931 to 4463 bytes, objects freed 21/44 (in 1 ms) - slots from 48/91 to 46/91
09:04:31.490 WIF: Checking connection...
09:04:51.486 WIF: Checking connection...

da werde ich mal schauen, auf 14 zubekommen und ggf das mit den Rules1

danke

[MagicBird]

OK habe die Eightree Dosen auf 14.4.1 bekommen.

Code: Alles auswählen

13:40:56.818 WIF: Checking connection...
13:41:03.060 BRY: GC from 9681 to 4813 bytes, objects freed 23/46 (in 1 ms) - slots from 52/91 to 50/91
13:41:16.870 WIF: Checking connection...
13:41:26.059 BRY: GC from 9649 to 4813 bytes, objects freed 23/46 (in 1 ms) - slots from 51/91 to 50/91
13:41:36.820 WIF: Checking connection...
13:41:49.058 BRY: GC from 9649 to 4813 bytes, objects freed 23/46 (in 0 ms) - slots from 51/91 to 50/91
13:41:50.553 HTP: Tools
13:41:52.628 HTP: Console
13:41:56.821 WIF: Checking connection...
13:42:12.061 BRY: GC from 9686 to 4813 bytes, objects freed 23/46 (in 0 ms) - slots from 52/91 to 50/91
13:42:16.821 WIF: Checking connection...
13:42:35.060 BRY: GC from 9629 to 4813 bytes, objects freed 23/46 (in 1 ms) - slots from 50/91 to 50/91
13:42:36.821 WIF: Checking connection...
13:42:56.820 WIF: Checking connection...
13:42:58.061 BRY: GC from 9629 to 4813 bytes, objects freed 23/46 (in 0 ms) - slots from 50/91 to 50/91

und nun dann sowas.

danke

[udo1toni]

Hast Du auch schon versucht, das Logging abzuschalten? (Siehe Menü in der Weboberfläche...)

[MagicBird]

Ok habe nun auf
Serial log "2 Info"
Web Log "2 Info"
Mqtt Log "None"
Syslog "None"

gestellt. war vorher alles auf 4 More debug

danke